FT-Slottechnik SCD2022 Carrera 15.5V Digital Decoder Chip

Item no.: SCD2022

FT-Slottechnik SCD2022 Carrera 15.5V Digital Decoder Chip - Ultra low profile.

Converts any brand 1/32 slot car to Carrera Digital 132, including NSR, Scalextric, Slot.it, Policar, Ninco, ScaleAuto, SCX, Fly, etc.

Fully compatible with Carrera Digital 132.  Ultra low profile ideal for those slot cars with bulky interior or low bodies.  Extra long wires, color coded to Carrera brand standards.

Package includes:

  • Assembled, ready to use decoder chip with extra long 4" feed and motor wires.
  • Plug wth wires for light assemblies, loose: three (3)
  • Pre wired IR-Diode sensor
  • Special Custom IR-Diode sensor mounting bracket
  • Instructions

Technical Specifications

  • Minimum operating voltage: 12.0 volts DC
  • Maximum operating voltage: 15.5 volts DC
  • Dimensions (L x W x H): 18.8 x 14.2 x 6.5 mm (4.5 without connector)
  • Weight: 2 grams
  • Angled plus
  • Longer connection cable
  • Underside without components
Special functions
  • Front light, rear light with brake light and auxiliary brake light
  • Ghostcar function
  • No accidental transcoding while driving
  • Stronger braking effect

Installation instructions
The decoder has to be fixed, e.g. by mirror adhesive tape (not included), into the chassis at the appropriate place. For mounting the IR diode a hole with a diameter of 3.0 mm has to be drilled in range of the front third and seen from above 12.5 mm left of the centerline of the chassis. The enclosed support for the IR diode has to be glued into the chassis in the region of the drilled hole and the IR diode hast to be mounted therein (hot glue recommended).
The decoder has separate connections for rear light and brake light. To use the built-­in rear-­ / brake light function on the rear light connection the soldering points (red framed on Figure 1) on the bottom of the decoder must be connected.

Decoder connections
Braids: Cable black = - / red = +, without plugs, tinned
IR diode: Cable black = - / red = +, IR diode soldered
Motor: Cable grey = - / purple = +, without plugs, tinned
Light: Plugs for enclosed light cords

Recommendations
Attaching a suppression capacitor parallel to the motor terminals (47-­100 nanofarads, not included).
Using series 3mm Standard LEDs in white or red with upstream resistance for better appearance (680Ω for white and 330Ω for red, not included).

Main Functions
To change settings the slotcar hast to be placed on the track in driving direction. Any change in the programming is confirmed by fast flashing lights. Any settings remain stored until a new programming is carried.

Encoding to an according speed controller
Start the encoding process by pressing the CODE button on the CU and complete the process by pressing the lane change button on the speed controller.
In the case of encoding by double pressing the lane change button on the speed controller please note a short break between the clicks (about 0.5 seconds). Furthermore, the vehicle must be de-­?energized at least 3 seconds before each encoding. The introduction of the encoding process is visually signaled by fast flashing lights after the first double pressing the lane change button on the speed controller.

Setting the basic speed
By pressing the SPEED button on the CU select the desired speed level and confirm by pressing the ENTER button on the CU.

Setting the braking effect
By pressing the BRAKE button on the CU select the desired braking level and confirm by pressing the ENTER button on the CU.

Light on/off
The slotcar must be located at least 3 seconds at a standstill on the track. Then the light can be switched on or off by pressing the lane change button on the speed controller.

USER MANUAL 2022

$43.99

Add to Cart:
  • Model: SCD2022
  • Manufactured by: SlotInvasion USA

Ask a Question

Manufacturer Info


Your IP Address is: 18.212.87.137
Copyright © 2024 LEB Hobbies, LLC - Built by PRO-Webs.net